RotoZip DC1 Duracut Bit Pack by Rotozip Product Tags: dc1 duracut, dc1 duracut bit, duracut, duracut bit pack, rotozip, rotozip dc1, rotozip dc1 duracut, rotozip dc1 duracut bit	Rating:  Read Reviews (8) Write Comments/Review Price Drop Alert Add to my Wish List Tag This Product

Compare Prices from 6 Stores:

Sort by:   Featured Stores (default) Price (low to high) Price (high to low) Store Name (A-Z) Store Name (Z-A)

Seller	Name	Price	More Information	Coupons / Promotions
	Amazon.com	Check Merchant's Website
	AbsoluteHome	$3.73
	Hechinger.com	$3.73
	Amazon Market Place	$7.30
	PlumberSurplus	$8.23
	Tool Barn	$9.30
	Ace Hardware	$17.49		$20 off on all Orders of $125 plus Free Ship to Store

Current User Reviews:	Back to top
More Review Pages:   1  2   Next >>
1 of 1 people found the following review helpful: GREAT TO CONCEAL SPEAKWIRE 1/5/2008 I used this to route a trough up my wall to conceal speak wire to my home theater speakers. It worked like a charm!!! My house is 1955 with plaster/mortar walls. I also used the dust extractor adapter - What a charm ABSOLUTELY NO DUST!!! If you have a Rotozip and a dust problem you need the dust extractor!!! Thank You. Was this review helpful?
2 of 2 people found the following review helpful: Works quite well in concrete board 12/8/2006 I bought this bit at home depot for $8 and used it to cut 4 sheets of hardebacker board into a circle for an outdoor mosaic table substrate, using a 3 1/4 hp router and trammel arm. The bit worked quite well, athough I noticed I had to get the RPMs up on the variable speed router to get it to cut easily. I doubt using this bit in a lower powered roto zip could've produced the same results. Perhaps the folks who don't like this bit should retry it in a router. Thank You. Was this review helpful?
8 of 8 people found the following review helpful: DuraCut Bit OK for soft to medium-hard materials 9/3/2005 RotoZip DC1 Duracut Bit Pros: - 1/4" bits have significantly greater resistance to breaking than 1/8" bits. It's still possible to snap one, but you have to use much more force. If you are frustrated with how easy it is to snap 1/8" bits, and your application will be OK with a 1/4" bit, try one of these. (Of course, the tool will need a 1/4" collet.) - Carbide cutters last much longer than tool steel. - Works quite well on soft materials, such as most wood, plastics, and drywall. Has an excellent life if used only on softer materials. They work best at very high speed. I.e., instead of a drill, try them in a router or high-speed rotary cutter. Cons: - As with any such bit, when the material gets harder, it becomes less effective -- to useless. E.g., using it on hard products will dull the bit in a hurry. E.g., porcelain or other hard tiles, concrete products such as blocks, bricks, concrete stucco (in spite of their sales pitch), glass, steel, etc. They work pretty well on some tile backer-boards, but this wears them out faster. Other: Cutting some materials, such as drywall, creates lots of dust. I use a respirator. Thank You. Was this review helpful?
6 of 6 people found the following review helpful: Cut what I wanted it to cut 8/9/2004 I have a 1940's home and bought this bit to cut the top of my living room wall's perimeter, just below the curve at the coved cieling because the walls are shot and need to be redone. My walls consist of 1/2 inch drywall with 1/4 + inch mortar, and 1/16 plaster and about 10 coats of paint. It's a DUSTY job, but the bit did it without a problem. I was just praying not to hit one of the drywall nails. For the home user, the tool is great and serves its purpose. Thank You. Was this review helpful?
10 of 10 people found the following review helpful: Great for plaster/buttonboard remodeling 11/10/2003 I am a remodeler and cutting plaster/buttonboard in older houses can be tough. I got only one hole cut for a six 6" can lights before my Greenlee hole saw was ruined. This bit in my Rotozip cut the last five and plenty of holes in the walls for outlets and for pulling wire (unlike a regular electrician I have to patch my holes so a square cut is worth it) . It did take a couple bits (you can see the "teeth" getting worn down) and near the end of a bit's life, you get more cutting by working the bit in and out. It's a dusty job and you should wear more than a cheap dust mask. I also found a full face shield worked much better than goggles. I have been trying to buy some more of these bits at Home Depot (couldn't wait for a Amazon order) but the clerk told me that Bosch had just bought out Rotozip and that it would be a while before new bits came in under the Bosch name(?) $10/bit is expensive but they get the job done. Thank You. Was this review helpful?
More Review Pages:   1  2   Next >>

Share your Comments or Review about this Product:

Back to top

Title/Summary: Your Comments or Review about this product: Your Rating?       I own this product. I want this product. I recommend this product. By submitting this form you acknowledge that you, not Plaza101, is responsible for the contents of your submission. All user submitted content becomes the sole property of Plaza101.com. Plaza101.com reserves the right to use, edit or delete user submitted content at its discretion.

Accessories:

1. Building Construction Illustrated

Similar Products:

1. RotoZip RZVAC1 Dust Extraction Adapter Kit
2. Factory-Reconditioned RotoZip RZ20-2100-RT Premium Cut-Off Kit
3. Bosch #SC5 5PK 1/8" Sabre Zip Bit
4. RotoZip XB-TC1 Tilecut X Bit
5. RotoZip SEG1 Straight Edge Guide Kit

Note: Displayed Prices are subject to change without notice.
Please check the merchant website for final price before making a purchase.

Read Reviews & Compare Price for RotoZip DC1 Duracut Bit Pack. Plaza101 helps you save money every time you shop online for RotoZip DC1 Duracut Bit Pack. Try this free shopping search service to compare products and stores to find the best online prices.